Y3635
Please keep this instruction sheet for future reference,
as it contains important information.
Requires four "AA" (LR6) alkaline batteries (not included) for operation.
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
CAUTION
This package contains small parts. For adult assembly only.
fisher-price.com
Consumer Information
WARNING
Prevent Entanglement Injury
• Keep out of baby’s reach.
• Remove mobile from crib or playpen when baby begins to
push up on hands and knees.
• This product may not attach to all crib designs. Do not add
additional strings or straps to attach to crib or playpen.
• Use ONLY attached to a crib or playpen.
IMPORTANT! Always attach with all provided fasteners tightly to a crib or playpen
according to the instructions. Do not add additional strings or straps to attach to a crib.
Check frequently.
• This product may be used from birth until 5 months.
• A crib mobile is intended for visual stimulation and is not to be grasped by a child.
• Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not
immerse this toy. The soft toys are surface washable.
• This toy has no consumer serviceable parts. Do not take this toy apart.
ICES-003
This Class B digital apparatus complies with Canadian ICES-003. Operation is subject
to the following two conditions: (1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
NMB-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit
pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
3
Battery Installation
1,5V x 4
“AA” (LR6)
We recommend using alkaline
batteries for longer battery life.
• Loosen the screws in the battery compartment door with a Phillips screwdriver and
remove the door.
• Insert four "AA" (LR6) alkaline batteries.
• Replace the battery compartment door and tighten the screws.
• If this product begins to operate erratically, you may need to reset the electronics. Slide
the power/volume switch on the mobile base off and then back on.
• When sounds or lights become faint or stop, it’s time for an adult to change the batteries.
• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of product in a fire. The
batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.
4
Assembly
Mobile Arm
Crib Connector
(Back)
Crib Connector
(Front)
Mobile
• Fit the front half and the back half of the crib connector to the mobile arm.
• Insert three 3,5 mm x 14 mm washer head screws into the back of the crib connector
and tighten with a Phillips screwdriver. Do not over-tighten.
• Fit the mobile onto the end of the mobile arm. Push to "snap" in place. Pull on the
mobile to be sure it is secure to the mobile arm.
5
Crib Attachment
Slot
B
Crib Top
Rail
A
D
Peg
C
1
• Fit the toy to crib top rail, facing the inside of the crib. Make sure the attachment strap is
A
on the outside of the crib
.
• Slide the end of the attachment strap down through the slot on the back of the toy
.
B
Pull the end of the attachment strap up and fasten to the slot on the peg on the back of
the toy
.
C
Note: This toy should be snug against the crib rail and spindles. Use the strap slot that
provides the tightest fit.
• If you have excess strap, slide the free end of the attachment strap through the opening
near the top of the attachment strap
.
D
6
Crib Attachment
2
• Tie the toy strings to a crib spindle.
Note: It is better the tie the strings in a knot than a bow, since a bow may be easily untied.
Bottom of toy
At Least
7 Inches (18 cm)
Mattress
3
• If the distance between the bottom of the toy and the mattress is less than 7 Inches
(18 cm), lower the crib mattress.
7
Music, Lights, Motion!
Start/Stop Button
Press the button to start the
music/sounds. Press the button
again to advance to the next
song. Press and hold the button
to stop the music/sounds.
Power/Volume Switch
ON with low volume
ON with high volume
OFF
Sound Select Switch
Nature Sounds
Music
Projector Switch
Projector Only
Projector and Lights
Mode Switch
Music & Motion
Music Only
Music & Lights
Music, Lights & Motion
Hint: The music/sounds will play for approximately 30 minutes. Lights and/or motion turn
off after approximately 10 minutes. Press the start/stop button to restart the lights/motion.
The music/sounds will slowly fade during the last 10 minutes of use.
8
|